Top 10 common forklift accidents ， forklift operation ought to take note of these matters ！.

Do not ignore the forklift at the workplace. If the operation is not good, there will be severe crashes in mins, and there are several crashes entailing forklifts.

Instance 1: The forklift freight obstructed the driver's sight, and the individual ahead can not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable width of the course and holds on the roadside rack, which practically causes an accident.
Instance 4: Forklift is speeding up and surrender during a turn.
Case 5: The forklift driver did not see the pedestrian, and the pedestrian did not see the forklift.
Situation 6: The forklift lifts the employees unlawfully, the forklift chauffeur does not wear the safety belt, the forklift lifter drops and the chauffeur is crushed when the forklift surrender.
Situation 7: The forklift driver did not put on a safety belt and fell from the vehicle when it surrendered and was crushed.
Forklift procedure must focus on these matters ：.

Beginning.
1. Before beginning, observe the environments, and after confirming that there are no barriers that impede the safety of driving, beep the horn first and afterwards start.
2. For lorries with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge have to be risk-free prior to starting.
3. When the forklift begins with a tons, the driver must first validate that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the height in between the bottom end of the fork and the ground ought to be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be raised too expensive, which will certainly affect the stability of the forklift. .
3. After discharging, the fork needs to be reduced to the regular driving placement before driving. .
4. When turning, if there are pedestrians or automobiles close by, the driving signal should be provided first. High-speed doglegs are prohibited. High-speed sharp turns will certainly trigger the automobile to shed side security and tip over. .
5. When the forklift is downhill, it is strictly prohibited to switch off the fire and slide, and it is restricted to brake suddenly while driving with tons unless there are special conditions.
6. When the forklift is running, it must obey the traffic rules in the factory and should keep a specific security distance from the automobile ahead. .
7. When the forklift is running, the tons has to remain in the most affordable position that does not impede the driving, and the gantry ought to be appropriately slanted back. The tons will not be increased except when stacking or loading. .
8. The height of the load must not obstruct the driver's view. In unique scenarios, when the product impacts the forward vision, drive at a low speed when reversing.
9. It is forbidden to activate the ramp, neither to drive across the ramp. .
10. The risk-free driving speed of the forklift in the manufacturing facility location is 5 km/h, and it needs to drive safely at a low speed when going into the production workshop area. .
11. When the forklift is raised, lifted or driven, it is forbidden for personnel to stand on the fork to hold things and play a stabilizing function. .
12. If problems are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with health problems or conceal them.

loading and dumping.
1. When fork-loading products, the distance in between the two forks should be readjusted as needed to make the load of both forks balanced and not manipulated, and one side of the product should protest the rack. .
2. It is restricted to collaborate with a solitary fork or use a fork top or draw. In special conditions, security indication need to be set up to advise bordering pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be sluggish and steady. Take care not to roll the wheels on the dunnage, so as not to stretch the rolled items and injure people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it must be noted that the fork idea need to not touch other items or items. The load ought to be maintained with minimal back tilt of the gantry to ensure that the lots does not slide in reverse. The pole can be tilted ahead a little when the load is reduced to enable very easy placement of the tons and removal of the forks. .
6. It is restricted to fork goods at high speed and hit tough objects with the fork head. .
7. When the forklift is working, it is prohibited for individuals to loaf the Stand-on Electric Pallet Stacker fork, so as to avoid the collapse of the goods and harm individuals. .
8. Straining is prohibited, and it is restricted to utilize forks to raise employees to take part in high-altitude operations to avoid high-altitude falling mishaps. .
9. It is not enabled to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to use forks to pick, turn pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the products on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the emergency brake button.
3. The engine is shut off and the power is cut off. (Except for special situations, such as the driver does not leave the car's line of vision and does not surpass 1 minute).
4. Remove the key. .

Forklift Operation Precautions.
1. Prior to and after the forklift procedure, the look must be inspected, and fuel, lubricating oil and air conditioning water need to be included.
2. Inspect the security performance of beginning, running and stopping.
3. Inspect whether the lights and horn signals are complete and effective.
4. Throughout the procedure of the forklift, inspect whether the pressure and temperature level are typical.
5. After the forklift is running, the outside leakage needs to additionally be inspected and the seals ought to be replaced in time.

Forklift Safety Operation Specifications.
1. You have to inspect Stand-on Electric Pallet Stacker before leaving the vehicle;.
2. When you encounter a person in front of you during driving, you need to send a signal at a distance of 5 m;.
3. The driving speed in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the nadir of the freight should be 0.3 m ~ 0.4 m in the air;.
5. The turning should not be also sharp to avoid the propensity of " complimentary turning";.
6. Adding and down the slope needs to be sluggish and consistent, and no switching on the incline is enabled.
7. Do not drive throughout the gradient. When the slope is above 10%, the vehicle must be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they come across large or heavy products and go to the motorist's line of sight, they must take the reversing exercise
.
The "Eight Prohibitions" need to be followed in the procedure.
1. Solitary fork operation is not enabled.
2. It is not allowed to lift the goods for cross country driving.
3. It is not allowed to get the goods by passing on the pallet with the fork.
4. It is not allowed to directly shovel chemicals, flammables and various other hazardous chemicals with forks.
5. It is not enabled to make use of inertia force to pick up the goods.
6. It is not enabled to make use of braking force to expatriation round or easy-to-roll things.
7. It is not allowed to bring people to service the pallet or fork, and it is purely restricted to stand under the fork after the fork is raised.
8. Do not drive laterally on inclines
.
Parking is not permitted under the following problems.
1. Contours, slim roadways, railway crossings;.
2. Sections with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the same length as the obstacle ought to be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844